Skip to content

do_breakdown_tok.m

Basic Information

  USAGE: [IM,figure_num]= do_breakdown_tok(IM_inputs,ramp_inputs, ...
                        model_inputs,figure_num,pcs_files,pause_it)

  PURPOSE: Calculates Best Initial Magnetization and Breakdown Trajectories

  INPUTS (defaults=[..]):
   structure IM_inputs (Initial Magnetization (& Breakdown Ramp) Input):
     flux0=       target flux at center (Vs) [3]
     bz_targ=     target vertical field scaler or (npt,1) (T) [-0.00015]
     ic_min       if exists => minimum coil current (A)  []
     ic_max       if exists => maximum coil current (A)  []
     npt=         Number of points on boundary for IM optimization [101]
     r_plasma=    Major radius of breakdown circle [1.8];
     z_plasma=    Z Location of center of breakdown circle [0];
     a_plasma=    Minor radius of breakdown circle [0.4];
     k_plasma=    Elongation of breakdown circle   [1.8];
     d_plasma=    Triangularity of breakdown circle [.5];

   structure ramp_inputs (Breakdown Ramp Input):
     times       time (s) interval for ramp, [0.001*[-12:1:12]'];
                   times(1)= start ramp from IM, (negative start time) [-0.012]
                   time=0 => breakdown time, (vector should have 0 in it)
                   time(end)= end of simulation [+0.010]
     iswtimes       [zeros(size(times))]
     Emx         Central Electric Field times(1)=> times=0 (V/m) [0.3]
     Emn         Central Electric Field at end of simulation     [0.2]
     volt_fac=   Voltage fractional increase for Ip calculation from VV EMF (1)
     li=         Plasma internal inductance [0.5]
     beta=       Plasma Beta [0];
     cejima=     Ejima coeficient for calculation of resistive flux [0.5];
     ip_factor=  Ip multiplier => reduce current requirement (and Bz) [1];
     decay_index= n=-Rp/Zpt*Br_pt/Bz =>  0 < n_stable < 1.5; [0.8]
     Vlimits =   voltage limits on power supplies [make limits proportional
            to Nturns: 1-turn_Volt*N_turn= Vterminal_voltage]
     slew_limit= Idot limit on coils [19.5e+3 = ~ 20kA/s]
     wbr    [200*[0, 1/sqrt(2) 1 1/sqrt(2) 0 1/sqrt(2) 1 1/sqrt(2)]']
     wbz    [200*[1, 1/sqrt(2) 0 1/sqrt(2) 1 1/sqrt(2) 0 1/sqrt(2)]']
     wbzdot =       [1]
     wpsidot =  [0.2]

   structure model_inputs:
     Vmat = (must be in PCS order)
     tok_data_struct
     cccirc=  PF circuit grouping
     vccirc =       [1:max(cccirc)]
     vvgroup= VV  grouping [vvid vvfraction] => 2 column matrix []
     nps   = number of power supplies
     scale_R_scpf [1]
     PSsys = power supply models (not used?)
     Rckt = resistances to add/replace coil resistance (essentialy 0) with
            switched in circuit resistors.  Order must correspond to internal
            states.

   General Control Input
     pcs_files=  0; 1= Ouput PCS files on completion, 0=no files [0]
     pause_it=   0; => no pause, 1= pause, # = pause(pause-it) [0];

  OUTPUTS: (primary output is "*.dat" files for PCS input [pcs_files=1])
   structure IM:
     icc_ohmic=   Optimum Ohmic Terminal Current vector  (A)
     ic_ohmic =   Optimum Ohmic Terminal Current vector  (A-Turns)
     ict_ohmic=   Optimum Ohmic Amp-Turn Current vector  (A)
     fl       =   Flux on Boundary (Vs)
     br       =   Br-field on Boundary (T)
     bz       =   Bz-field on Boundary (T)
     rpt zpt  =   R,Z boundary points used in analysis (m)
     err      =   Average Error in booundary flux value (Delta_Vs/Vs)

  Plots:
     figure(1): geometry -- Flux contour -- cccirc numbering -- coil current
     figure(2): geometry -- B-field contour -- A-turn for full coil system
     figure(3): flux variation around circumference of breakdown circle
     figure(4): B-field variation around circumference of breakdown circle

  RESTRICTIONS:
     uses standard tokamak vacuum objects for all magnetics
     Produces Amp-Turns.  Should work on any tokamak but needs gneralization
     of cccirc code.

  METHOD:
     Determine optimum Coil current distribution using least square technique
     to produce a uniform 1 Vs flux on the boundary see ohmic_dist.m

Dependencies