Skip to content

bgreens_fine.m

Basic Information

  @(#)bgreens_fine.m    1.4 02/11/08

  SYNTAX: [brgreens,bzgreens,bpgreens] = ...
        bgreens_fine(coil_data,bprobe_data,nrect,verbose)

  PURPOSE:  Compute Greens functions from axisymmetric current carrying
    conductors, each of whose cross-section is a parallelogram, to Br,
    Bz, and angled probe measurement at a set of specified points.
    This version of code is based on low level calculation using fine.m.
    Can be used to compute Br,Bz Greens functions for arbitrary points in
    space.

  INPUT:
    coil_data = data describing geometry of coil set
       Format of this data has each column = [Z;R;dZ;dR;AC;AC2], where:
        Z   = z centroids of conductors (m)
        R   = r centroids of conductors (m)
        dZ  = height of conductors (m)
        dR  = width of conductors (m)
        AC  = angle between coil and horizontal (degrees)
        AC2 = angle between coil and horizontal (degrees)
    At most one of AC, AC2 is nonzero and indicates type of parallelogram:
                                xxxx
                            xxxx   x
                        xxxx       x
                    xxxx           x       ---                 xxxxxxxxxxxxx
                xxxx               x        |                xx         xx
       ---  xxxx                   x        |              xx         xx
        |   x          X        xxxx      dZ             xx         xx
        |   x        (R,Z)  xxxx            |          xx   X     xx
      dZ    x           xxxx                |        xx   (R,Z) xx
        |   x       xxxx                    |      xx         xx
        |   x   xxxx                        |     xx         xx
       _|_  xxxx   ^                       --- xxxxxxxxxxxxx    ^
                 AC )                                        AC2  )
            |----------dR----------|           |---dR------|

    bprobe_data  = Bprobe data, 5 x number of probes (or any msmnt pts):
        bprobe_data(1:6,:)=[Z;R;Ang;length(m);Ip coeff;width(m)]
     (abs(4th row) specifies width if < 0)
        (5th row is ignored, so 4 x number probes also works)
     (6th row is optional, assumed 0.02m if not provided)
    nrect = rectangle partitioning for conductor set (see header
        documentation for bld_subelements.m)
       verbose = print/display verbose info.  0 = no print/display.  Numbers>0
               give increasingly more information/displays.

  OUTPUT:
    brgreens = Br Greens function matrix, with rows corresponding to probes,
        columns to conductors (Tesla/MA)
    bzgreens = Bz Greens function matrix, with rows corresponding to probes,
        columns to conductors (Tesla/MA)
    bpgreens = Greens function matrix to field measured by bprobes, with
        rows corresponding to probes, columns to conductors (Tesla/MA)

  RESTRICTIONS:
     If probe width is specified in 6 row bprobe_data AND there is length<0
     in row 4, the row 4 specified length prevails. Probe will be treated as
     flat if width specified in row 4 (6 row convention allows l & w)

  METHOD:  Each conductor is partitioned into a bunch of tiny rectangles.  All
    bgreens are computed for these rectangles, then combined at the end.
    Calculation is done in 2 steps:
    (1) use filament to filament calculation for all subelements
    (2) replace those subelement calculations which would have inaccurate
    results, based on geometric information, with more accurate calculation.

  WRITTEN BY:  Mike Walker  ON  7/26/99
  10/03/03   JAL1   remove one line commented below
  10/30/07   NWE    length=0 "saddle probes" treated as single point
  02/08/08   NWE    applies probe cross section width if specified in
                    bprobe_data(6,:) or length<0 in bprobe_data(4,:).

Dependencies